[Histonet] Mixing Paraffin Brands

[Manfre, Philip]

Hey Pedro,
	How are you?  We sometimes  use T-555, which is a little firmer.

Phil.

Philip Manfre, B.A., HT (ASCP)
Associate Principal Scientist
Merck Research Laboratories
WP45-251
PO Box 4
West Point, PA 19486

215-652-9750
215-993-0383 (fax)
philip_manfre <@t> merck.com





-----Original Message-----
From: histonet-bounces <@t> lists.utsouthwestern.edu [mailto:histonet-bounces <@t> lists.utsouthwestern.edu] On Behalf Of Louro, Pedro
Sent: Wednesday, June 19, 2013 2:33 PM
To: Rene J Buesa; Lucie Guernsey; histonet <@t> lists.utsouthwestern.edu
Subject: RE: [Histonet] Mixing Paraffin Brands

Just out of curiosity, what paraffin would people out there recommend using for animal bone joints and turbinates?
We are currently using parapalst plus and was thinking of changing to a "harder paraffin"

Any thoughts???

Pedro L.


-----Original Message-----
From: histonet-bounces <@t> lists.utsouthwestern.edu [mailto:histonet-bounces <@t> lists.utsouthwestern.edu] On Behalf Of Rene J Buesa
Sent: Wednesday, June 19, 2013 2:24 PM
To: Lucie Guernsey; histonet <@t> lists.utsouthwestern.edu
Subject: Re: [Histonet] Mixing Paraffin Brands

Each paraffin has some additives to improve either its penetration rate or density to section.
Mixing different melting points (MP) paraffin will result in another paraffin with an intermediate MP and the sectioning will be different.
Preparing the block with the mixture will probably cause so troubles while sectioning.
Why don't you just use them separate? There is no good reason to mix them and the two paraffins you mention are of good quality.
René J.

From: Lucie Guernsey <lguernsey <@t> ucsd.edu>
To: histonet <@t> lists.utsouthwestern.edu 
Sent: Wednesday, June 19, 2013 2:01 PM
Subject: [Histonet] Mixing Paraffin Brands


Hi,

Does anyone know if there's a reason why one shouldn't mix different brands
of paraffin? We normally use Fisherbrand's Paraplast Plus (melting point 56
C). We inherited about 8 bags of McCormick Paraplast X-tra (melting point
52 C). Will the different melting points be a problem?

If we were to use the McCormick paraffin, the only place it may mix with
the Fisherbrand paraffin is in the blocks themselves (as we refill the
embedder). But I don't want to compromise the quality of our blocks just to
not waste the free paraffin.

Or, another option could be that we use the McCormick in the processor and
the Fisherbrand in the embedder. Could that cause issues in the blocks as
the tissue would be infiltrated with one brand and embedded in another?

Maybe I'm over-thinking this......

Many thanks!
Lucie

Lucie Guernsey
UCSD
Dept. of Pathology
lguernsey <@t> ucsd.edu
_______________________________________________
Histonet mailing list
Histonet <@t> lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet
_______________________________________________
Histonet mailing list
Histonet <@t> lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet

********************************************************************************************
Our Values:  Excellence, Drive, Ownership, Challenge, Teamwork, Respect
********************************************************************************************

LEGAL NOTICE
This message is confidential and contains information which may be legally privileged. It is intended for the stated addressee(s) only. Access to this email by anyone else is unauthorised. If you are not the intended addressee, any disclosure or copying of the contents of this email or any action taken (or not taken) in reliance on it is unauthorised and is unlawful. If you are not the addressee, please inform the sender immediately and destroy the original message.
The data in this email will have been screened for the presence of computer viruses known by the Company at the time the email was produced. The Company cannot guarantee, however, that the email or any attachments are virus free. Delivery of the email will be at the Client's risk.
Registered in England No. 1815730
VAT Reg. No. GB425507072
Registered Office: Woolley Road, Alconbury, Huntingdon, Cambridgeshire PE28 4HS
**********************************************************************


_______________________________________________
Histonet mailing list
Histonet <@t> lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet
Notice:  This e-mail message, together with any attachments, contains
information of Merck & Co., Inc. (One Merck Drive, Whitehouse Station,
New Jersey, USA 08889), and/or its affiliates Direct contact information
for affiliates is available at 
http://www.merck.com/contact/contacts.html) that may be confidential,
proprietary copyrighted and/or legally privileged. It is intended solely
for the use of the individual or entity named on this message. If you are
not the intended recipient, and have received this message in error,
please notify us immediately by reply e-mail and then delete it from 
your system.